Dry Edible Beans: Harvest and Storage

Excerpt from Agronomy Guide for Field Crops (Chapter 7)

Order OMAFRA Publication 811: Agronomy Guide for Field Crops

Table of Contents

1. Introduction
2. Pulling, Windrowing, Combining
3. Direct Combining
   • Average White Bean Harvest Loss in 1990 and 1991 - Table 7-6
4. Quality Preservation at Harvest
5. Updates on Dry Edible Beans: Harvest and Storage
6. Related Links

Introduction

Producing beans that are clean, bright and whole is the ultimate goal. Edible beans can be a sensitive crop to harvest. Weather conditions in the fall can cause some bean types to deteriorate in quality much quicker than others. Kidney, dutch brown and black beans tend to withstand more adverse weather at maturity than the white navy, cranberry and white kidney types. Larger, seeded coloured beans tend to absorb more moisture after a rain, requiring more time to dry down. It is therefore important to know the quality standards for the market class you are selling to.

The recommended range of moisture for harvest is 16%-20%. Harvesting outside this range will greatly reduce quality. Low moisture contents will increase the levels of split seeds and cracked seed coats. Wet or immature beans will become stained from the leaves, stems and dirt.

There are two common methods of harvesting dry edible beans: pulling followed by windrowing or direct-combining.

| Top of Page |

Pulling, Windrowing, Combining

Beans planted in wide rows are usually harvested after pulling, which cuts the plants 3-5 cm (11/4 in.) below the soil surface, and pulls plants from two or more rows into a single row with a windrower. Beans are pulled when 90% of pods have matured and turned buckskin brown. To prevent pod drop and shattering losses, beans should be pulled early in the morning when the plants are damp with dew and tough. Beans are harvested later the same day with an edible bean or conventional combine equipped with a windrow pick-up attachment. Since prolonged exposure of the mature crop to excessive moisture will result in lowered quality, it is important to harvest the crop as soon after pulling as possible. Larger-seeded bean types require specialized combines in order to meet quality standards set by the market. Under good conditions, seed losses of 3%-5% are normal during harvest (i.e., 1% loss pulling and windrowing, 1% at combine pick-up, and 1%-2% cleaning and threshing).

| Top of Page |

Direct Combining

Bean types most suited to direct harvest include white beans with upright plant type, adzuki beans, black beans and pinto beans. Larger-seeded bean types require specialized combines in order to meet the quality standards of the market.

Combine enhancements help to reduce harvest losses and minimize dirt, splits and damage to the beans. The cleaning and threshing characteristics of the crop will change throughout the day as moisture content changes. Combine set-up should include:

• Knives kept sharp to minimize shatter losses.
• Cylinders run only fast enough to thresh crop. Run as much material as possible through the cylinder to minimize seed damage. Cylinder speeds on many combines do not go below 250 rpm, which can be too fast for easily threshed beans. Cylinder slow-down kits, which include a smaller diameter drive pulley and a belt, are available.
• Unloading augers run slow and full to minimize seed damage. The short vertical auger on the combine (turret auger), which takes seed from the bottom of the tank to the main unloading auger is a point of high seed damage. Some bean growers have changed unloading augers to conveyer belt systems.
• Combine ground speed set at about two-thirds slower than when harvesting soybeans.
• Vine lifters raise low hanging pods before the plant is cut. This can be of the greatest benefit in harvesting varieties without a strong upright plant type.
• Flexible floating cutter bar adjusted to clip the bean plants as close to the ground as possible. This will help minimize the cutting of low-hanging pods and associated seed loss. The knife must cut cleanly and quickly to avoid shaking the plants, splitting pods and shattering beans. Most losses that occur are shatter loss. Ontario studies have shown that a flexible floating cutter bar can reduce losses by 25% compared to a conventional floating header. In addition a "quick-cut" sicklebar reduced loss by up to 40% compared to a standard sicklebar. Table 7-6. Average White Bean Harvest Loss in 1990 and 1991, displays the results from harvest loss comparisons made between four harvest methods on several farms in Michigan in 1990 and 1991.
• Use of an air reel to significantly improve intake of plants into the combine and reduce losses at the knife. The air blast keeps weeds and bean plants off the knife, offering better cutter bar visibility without shoving stones into the header. The biggest benefit of the air reel is established under difficult harvest conditions, when the crop is lodged or the volume of crop is reduced. Under good conditions, harvest losses may be as low as 3% regardless of whether or not an air reel is used. Late in the day as pods dry, header losses can reach more than 20% with a standard pick-up reel, while losses with an air reel are only 10%.
• A modified harvest pattern to improve yield and quality. Travelling against the direction of lodging allows the harvest of leaning branches and low-hanging pods and can reduce stubble losses by up to 300%. In an uneven maturing or weedy crop, delay harvest in the affected areas until they are mature or they can be treated with a desiccant.

| Top of Page |

Source: Harvesting Michigan Navy Beans, Michigan State University.

¹Includes only those trials where equipment was operating as intended.

Quality Preservation at Harvest

Occasionally, the crop may be ready to harvest but the field or part of the field may still be green or weedy. Harvesting when green stems or green weeds are present may result in stained beans. Products are available for harvest aid to burn down weeds and desiccate the crop. Refer to OMAFRA Publication 75, Guide to Weed Control, for more information. Similarly, weeds such as Eastern black nightshade and American pokeweed can cause severe staining. Where direct harvest is intended, a desiccant should be applied to dry the remaining green tissue. (Order OMAFRA Publication 75)

Secondary growth can occur as plants begin to mature, particularly when rainfall follows an extended dry period. White beans are more susceptible to secondary growth than coloured beans.

Special effort should be taken to maintain seed quality. Before harvesting, the combine should be cleaned of any residual seed of previously harvested crops. If on-farm storage is necessary, store individual varieties of beans in separate bins that are free from other grains and oilseeds. Harvested beans should be kept free of stones, glass and other seed-size contaminants. Failure to maintain the purity of the crop can result in lost value.

| Top of Page |

Updates on Dry Edible Beans: Harvest and Storage

No updates available at this time.

| Top of Page |

Related Links

• Dry Edible Beans

| Top of Page |